➤ CalAmp

The brands we had chosen to go with for the past years have done us very well and are competitive plus never had any issues or breakdowns..

Dear Evgeny

Here is a Calamp-Wialon question.  At now seems only voltage-type fuel level sensors are supported. But digital interface will provide better results and precision.  Several Wialon users want to use them, but we need to solve a simple problem.
Calamp LMU 2700 uses RS232 port for Text messaging. We have built a special firmware for Calamp and now LMU device receive volume value and send to Wialon. But in text field as "user_msg_1" parameter

Any chance to convert them to sensor value, for example : from "554" to 554?

Thanks!

EDIT : Now digital fuel level sensors are working with Calamp via RS232 interface

Hi everyone,

AM looking for the correct calamp Sregister or parameter to set inorder to get my calamp units showing steadily online in wialon local. What happens now is that my unit comes online for 10minutes if I run the AT command AT$APP CLEAR LOG. After 10 minutes it shows offline until I run the AT command again. Am testing these units on the bench and cannot install it I get them showing online steadily.

Kindly help.

BR,

Bilal

Here is it a 15 Lines Minimalist ol' School AT script for any calamp devices

0.-AT$APP GPRS CONTEXT 0 "your_apn"    //APN
1.- AT$APP PPP USER "apn_username"                        
2.- AT$APP PPP PASSWORD "apn_pswd"                
3.- AT$APP INBOUND 193.193.165.165:port     // Port depends on LMU model, pls see  http://gurtam.com/en/hw-manufacturers/calamp                  
4.- AT$APP PARAM 262,0,30                    //Time Distance Profile 0 (Time=30 secs)
5.- AT$APP PARAM 263,0,800                    //Time Distance Profile 0  (Distance=800m )
6.- AT$APP PARAM 264,0,60                    //Time Distance Profile 0  (Heading=60є)
7.- AT$APP PARAM 265,1,900                    //Timer 1 = 15 min for reports when unit off
8.- AT$APP PARAM 512,0,3,0,0,0,7,0,0,0      // Start  time-distance profile 0 on reset  OR power up
9.- AT$APP PARAM 512,1,16,0,0,0,6,0,0,0     // When Ignition off stop actual profile running
10.-AT$APP PARAM 512,2,16,0,0,0,13,1,0,0   // When Ignition off start timer 1 ()
11.-AT$APP PARAM 512,3,18,1,0,0,1,10,0,0    // When timer ran out send report (EVcode 10) Unit off reports
12.-AT$APP PARAM 512,4,17,0,0,0,1,11,0,0     // When Time-Distance updates send report (EVcode 11) Unit on reports
13.-AT$APP PARAM 512,5,16,0,0,0,1,12,0,0     // Send EVcode 12 when Ignition Off
14.- AT$APP PARAM 512,6,15,0,0,0,1,13,0,0      // Send EVcode 13 when Ignition On

Event Codes
10 Reports when Unit is Off (parking)
11 Reports when Unit is Moving
12 Ignition Off
13 Ignition On

Hope can be useful !!

Por favor necesito la comfiguración para reportar cada 30 segundos con ign on y cada 5 minutos con ign off

small_gprs пишет:

Here is it a 15 Lines Minimalist ol' School AT script for any calamp devices

0.-AT$APP GPRS CONTEXT 0 "your_apn"    //APN
1.- AT$APP PPP USER "apn_username"                        
2.- AT$APP PPP PASSWORD "apn_pswd"                
3.- AT$APP INBOUND 193.193.165.165:port     // Port depends on LMU model, pls see  http://gurtam.com/en/hw-manufacturers/calamp                  
4.- AT$APP PARAM 262,0,30                    //Time Distance Profile 0 (Time=30 secs)
5.- AT$APP PARAM 263,0,800                    //Time Distance Profile 0  (Distance=800m )
6.- AT$APP PARAM 264,0,60                    //Time Distance Profile 0  (Heading=60є)
7.- AT$APP PARAM 265,1,900                    //Timer 1 = 15 min for reports when unit off
8.- AT$APP PARAM 512,0,3,0,0,0,7,0,0,0      // Start  time-distance profile 0 on reset  OR power up
9.- AT$APP PARAM 512,1,16,0,0,0,6,0,0,0     // When Ignition off stop actual profile running
10.-AT$APP PARAM 512,2,16,0,0,0,13,1,0,0   // When Ignition off start timer 1 ()
11.-AT$APP PARAM 512,3,18,1,0,0,1,10,0,0    // When timer ran out send report (EVcode 10) Unit off reports
12.-AT$APP PARAM 512,4,17,0,0,0,1,11,0,0     // When Time-Distance updates send report (EVcode 11) Unit on reports
13.-AT$APP PARAM 512,5,16,0,0,0,1,12,0,0     // Send EVcode 12 when Ignition Off
14.- AT$APP PARAM 512,6,15,0,0,0,1,13,0,0      // Send EVcode 13 when Ignition On

Event Codes
10 Reports when Unit is Off (parking)
11 Reports when Unit is Moving
12 Ignition Off
13 Ignition On

Hope can be useful !!

Hello,
I'd calAmp OBD2 devices, we previously(last 2yeares) used MODUS telematic, but now their stop service, and now we'r using wilon, I want to changed wialon server address for this calAmp OBD2 devices, but I don't have any tools, Can anyone help me please?  kindly check attached for my product photo.

PS: I'd try download PEG programing guide from your previous forum, but not reachable,

Thanks in advance,

BR,
Zau.