1Тема от sistelcosoporte

How configure Omnicomm optim Ignition

  • Зарегистрирован: 09/12/2016
  • Сообщений: 79
  • Карма: 8

Тема: How configure Omnicomm optim Ignition

Hello everybody!!!

I recently bought a new GPS device Omnicomm Optim.  But I dont know how configurate the ignition sensor in the plataform Wialon.
AVL hardware supported by wialon there are 1166 Omnicomm Optim devices alredy installed.
Anyone knows how create the ingnition sensor on the wialon plataform?

Thanks

-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Hola a todos!!!

Recientemente he comprando un nuevo dispositivo GPs omnicomm optim. Pero no se como configurar el sensor de encendio en la plataforma de wialon. Los equipos soportados por wialon son 1166 Omnicomm Optim ya instalados.
Alguien sabe como crear el sensor de encendido en la plataforma de wialon?

Gracias

0
2Ответ от serd

How configure Omnicomm optim Ignition

  • serd
  • Wialon fan club
  • Карма: 3

Re: How configure Omnicomm optim Ignition

hello,

not sure, that those settings are the same for all FW versions + you also will have to configure the device itself and ignition can be connected (usually) to several inputs of the tracker etc. etc. etc.

So there is basically a universal approach - you look over raw data from the tracker (in the messages tab) and find the parameter, create an ignition sensor, verify it and then use for all devices of that type.

In case there are difficulties with that - send us a note to support@gurtam.com and make sure to give us access + unit name and we'll try to assist you with that.

0
3Ответ от small_gprs

How configure Omnicomm optim Ignition

  • Откуда: CDMX
  • Зарегистрирован: 10/04/2010
  • Сообщений: 293
  • Продукты: Wialon HostingWialon Pro
  • Карма: 50

Re: How configure Omnicomm optim Ignition

Create a bitwise sensor using right bit in flg status byte, it's a cake, and optim terminals rocks !

--
Spread the AVL- World

0
4Ответ от jommi

How configure Omnicomm optim Ignition

(18/04/2017 17:26:03 отредактировано jommi)
  • jommi
  • Wialon fan club
  • Неактивен
  • Зарегистрирован: 24/03/2017
  • Сообщений: 19
  • Карма: 0

Re: How configure Omnicomm optim Ignition

@small_gprs
can you explain how to create a bitwise sensor with the right bit in flg status byte?

0
5Ответ от zark

How configure Omnicomm optim Ignition

  • zark
  • zark
  • Gurtam
  • Неактивен
  • Зарегистрирован: 05/09/2014
  • Сообщений: 686
  • Продукты: Wialon Hosting
  • Карма: 227

Re: How configure Omnicomm optim Ignition

If some parameter (e.g. "status") contain information in one of the bits (e.g. the fourth), you can use the following expression -- status:4
Please, notice, that bit number is counted not from 0, but from 1 in Wialon.

@ Oleg Zharkovsky
Customer Service / Quality Control and Training
"Timely is the best. But still better late than never."

Сайт zark

0